Blogs

Jan 27,2022

How Plumbing Issues Is Solved Using The Right Tools

Pressing pipe problems are almost always caused by failure to calculate pipe lengths correctly. If the pipe is not cut long enough, the pipe will be too short. If it is cut too long, there will be an excessive amount of pipe sticking out of the fitting or connection that must be removed with a pipe cutter or hacksaw blade. The second most common problem with pressurizing water lines is improperly gluing joints. The job of adhesives in the pipework is to prevent leakage, not to provide structural strength for holding up pipework. Pressurized water supply systems should never rely on adhesive alone for support. A good rule-of-thumb states that every section of 2" pipe should have at least one threaded end connection. Pipe Cutting Service The pipe cutter is used to cut pipe cleanly and squarely, leaving no burrs for bacteria or other contaminants to hide. The pipe that is not cut square will usually leak at the joints. It may also be necessary to remove metal from the pipe with a reamer to fit correctly in the fitting. Reamers can be either hand tools or power tools designed specifically for this purpose. Hand reamers are available in sets of large sizes, each one removing just enough pipe material to fit into another size fitting until they reach one small enough for the job; these are preferable because they leave only slight nicks behind, which do not weaken the pipe or require cleaning up before gluing (which happens when complete pipe sections are removed). Pressure Testing Service The piping system has been checked under normal operating pressures for 20 minutes with no loss of water or air from any part of the system. Leaks have been repaired where necessary and defective parts replaced. Types Of Pipe Fittings For Your Home There are different pipe fittings to choose from for your home. A pipe bender is an important tool for a plumber since it is the only way to make accurate radius bends in the pipe. Pipe benders come in several styles, but all of them use pressure or springs against a curved form to bend the pipe around until it fits into another fitting. Some pipe benders automatically feed the pipe as they turn it around the form, others require that new lengths of pipe be cut and inserted into the device before using again. The pipe that comes out of a pipe bender must always be checked with a straight edge to ensure a proper fit on both ends, and pipe benders should never be used to straighten pipe that has pipe bender or hand-bend marks on the outside of the pipe. What Is A Pipe Joint? There are many different types of pipe nipples and joints for joining pipe together, including threaded, compression, solvent, and soldering. A general rule states that every fitting must have at least one threaded end so it can effectively bear the brunt of water pressure. Compression fittings require to insert rings or nuts which press against the inside of the pipe and hold it in place while a ring nut compresses them around both sides of the pipe; these fittings work well with plastic pipes but often leak when used with metal pipes because they tend to rust over time and shrink slightly. Types Of Pipe Joints A pipe joint is the fitting that joins two pipe sections or pipe fittings together; pipe joints are either threaded or solvent, but both must be thoroughly cleaned before they are glued into place. Threaded pipe joints use screws to seal them, making them appropriate for joining metal pipe sections together; solvent pipe glues work well with a plastic pipe because they do not corrode it as metal does. Solvent pipe glue should never be used on steel piping; the only type of glue recommended for this material is threaded pipe joints or welded fittings. Home Pipe Problems Your home's pipe problems can be identified, which leaves you with the task of choosing the best pipe to solve it. Depending on what is causing your pipe problem in your home, understanding all of the different pipe types will help you choose the correct pipe for you specific job or repair. Knowing what each pipe type is called and how they are used when plumbing will help when speaking to a plumber so he can properly diagnose your issue. Leaking pipes in walls, sinks, showers and toilets are all common issues that homeowners fix by themselves when they know enough about pipe material and types to choose which type works best for their unique problem. Toilet tank leaks caused by using old parts may require replacing everything in order to stop the leak, while pipe problems in a shower can often be repaired by simply replacing a pipe fixture. Metallic Pipe Fittings Metallic pipe fittings use threaded pipe joints or welded pipe, which means that each fitting is held together by a pipe thread that screws into another fitting with an o-ring seal. Depending on how tightly it has been screwed, some metallic pipe fittings may not form a watertight seal between the two parts when they are put together. In this case, tightening too much can strip the threads inside of your pipe joint and make it useless for any sort of job application; stripping the threads damages the metal so badly that most plumbers choose to replace faulty pipe fitting instead of attempting to repair it. Sink pipe clogs can often be removed by using a pipe wrench to twist and remove the pipe fitting, and it is recommended to use pipe joint compound on all pipe threads before screwing pipe fittings together to ensure the best watertight seal possible. Plastic Pipe Fittings Plastic pipe fittings are glued into place with solvent glue or thread-sealing tape; like metallic pipe joints, they both must be tightened enough for an o-ring seal to form around the outside of your piping system. Plastic pipe fittings come in plastic tubing that can be cut with a saw or scissors, but they also come as small pieces that you snap together depending on how many parts you need for your installation job. If you are planning to use pipe joint compound to make your pipe fittings watertight, it is best to do so before the pipe fitting pieces are put together. Solvent glue pipe fitting connections will become weaker once they are taken apart and then re-glued; this means you should wait one day after gluing the pipe fittings together before adding pipe joint compound because you want them to stay in place while the solvent glue has time to dry completely. Benefits Of Using High Quality Pipe Fittings Pipe fittings are not all the same. Some pipes may have high-quality pipe fittings, which are generally used in pipe systems. There are many benefits of using them and one should not compromise on the quality of the pipe fitting when it is purchasing it for little or big jobs. Many people think that cheap pipe fitting will do the job just fine, but they fail to realize several issues associated with buying it. If you buy a poor quality pipe, it can result in low flow rate, reduced pressure, rust formation inside your system, blockage of pipes, etc. So you need to confirm if you are getting value for money or wasting money by investing in something inferior product. Using High Quality Pipe Fittings These pipe fittings are made of good quality materials that ensure that they last long. Low-quality pipe fitting cannot last for a considerable amount of time because they are very fragile. You will have to replace them in no time when using low-quality pipe fittings which is again an additional cost. High-quality pipe fitting saves money and increases the life span of pipe systems. This way, you save more in the long run by investing once at the initial stage rather than replacing pipe joint or pipe fittings frequently. - Low flow rate, reduced pressure, rust formation inside your system, blockage of pipes etc are some problems caused by buying cheap pipe fitting. These issues do not arise when you use high end pipe fittings which ensures that pipe system is safe for use. - These pipe systems will last longer and provide the best pipe fitting performance without any problem. It can be used in all types of domestic and commercial pipe systems and areas, increasing its demand due to its long-lasting impact. With the advancements in technology, pipe fittings are made available at affordable prices these days. However, very low-priced pipe fitting means that you are compromising on the quality offered by the product. Certain pipe fitting products keep high-end applications in mind, while others are only for essential purposes since they have to suit every pocket of buyers. So before making investment decisions, ensure what kind of pipe fitting you need to make the correct purchase decision.

Jan 14,2022

Some of the main classes of plumbing work

Plumbing can be a confusing subject for those who aren’t sure of the difference between their own plumbing needs and others'. If you are like most homeowners, you have no doubt done some basic plumbing work before. However, there are many other aspects to plumbing that are important to know in order to prevent potential issues with your home. Most people know that plumbing is important, but they may not know exactly what it does. We’ve got some good information to show you what plumbing actually is, and how it affects the lives of everyone from astronauts to construction workers. Before We Get Further Into The Topic, You Might Want To Know What House Plumbing Is Based on the same principle as electricity and other similar technologies, water systems have become common in recent years thanks to various developments from the plumbing industry. Currently, most industrialized nations use some form of water system for their military operations or drinking water needs because it's easier to ensure access and reliability than a simple well or rainwater collection tank. Water systems can also be used for irrigation of crops, water collection for domestic use and providing water to homes as well. Saving money can be done by staying on track with what the plumbers are doing when there is a leak or problem that needs attention. You do not want to go into your budget in June and find out you have tens of thousands of extra dollars because all those months you weren't careful enough so now figuring out how much it will cost. It’s required to keep a close eye on your plumbing in the winter months. Also, if you find that there is water coming up from your sewer line outside it is essential that you call an experienced plumber right away and have them come out and clear the problem immediately. Main Types Of Plumbing There are three types of plumbing that come into play with basic washroom installations; soil or water pipes, hot and cold running pipework, as well as pressure pipes. Sewage systems adopt many features similar to those used for potable water supply - such piping is usually made from PVC reinforced plastic and runs through the earth horizontally beneath residential properties (usually under the house) ending at a sump that collects all waste products from inside your home. Soil pipes take waste products to the sewer system. They generally run horizontally under grass and parking lots, which flow through underground sewers before reaching a sewage treatment plant. There are instances when these systems may include wells or pumping stations for groundwater supplies that do not need to enter local waterways through storm drains nor cross-property boundary lines. Important Equipment Used In Plumbing Many important and critical items used daily in residential plumbing installations, such as hose connectors, carbon pipe nipples designed for water off-take valves or the main drain valve are unreasonably costly if purchased separately especially considering their low volumes sold on a per-piece basis. Other key types of equipment include: For instance, a unique sealing device is generally used to seal the openings of sewer pipes after plumbers alter them. The material that such packing is made from is known as filler; it should be nontoxic and not at all harmful or hazardous towards human health--this applies for both granular types and self-forming plastic materials like polyvinyl chloride (PVC) that may pose an independent danger on their own if left in contact with the skin for longer than expected. The Main Parts Of The Plumbing Plan Plumbing plans are great assistance for residential property owners, architects, and home builders in setting up the way each part of their house works together. This is because working and planning plumbing pipes perfectly in each room or the accessible area will create smooth running water to flow throughout all parts of the house. Hence knowing where things go can be quite useful over time as mistakes run along with wasted money especially during larger grading phases involving many contractors undertaking numerous projects at one time. Planning is also important in setting up precisely which pipes will take the most pressure and which ones should be maintained at the minimal operating level and being of reasonable distance from each other. There are many strategic break-even levels where water flow probably would not stop flowing even with small or large problems like leaking hoses, broken pipe connections, or pumps that fail to remove a great deal of the right amount falling off water byline over time. For this reason it is key to take a look at trends in plumbing supplies and materials, which can differ from area to another. This way, all contractors working on the project will better understand when they are ready for solutions such as longer pipe lengths or different kinds of connections being installed instead, etc. Main Plumbing Tools Are: Install and change any of the above pieces for smaller projects can be done with a few simple hand tools. For big enough jobs like major upgrades to existing plumbing systems or even entire new installations that require tons of materials such as steel close fittings in place, ladder stands may become necessary for highly advanced craftsmanship techniques. To keep the organization on top of your business, it's important to have a good system in place for managing tasks and communication. With regards to work assignments, you can use an effective project management tool or service such as Estimate Works. When communicating with employees, like shop foremen or plumbers, you may use blogs with forum discussion threads underneath and communicate via RSS feed. Then finally, at the end, just manage all communications with an effective checklist software. Prices of plumbing tools and equipment have been dropping since the early 2000s. Prices are now stable, with some sharp increases taken by concrete-cored drill bits in recent years. Snubbing pliers or pipe cutters make good disposable hand tools for installing couplings at the corners of tubular piping systems; however, it is not recommended to use them as part of an installation method.

Jan 12,2022

Pipe nipples- fixing all your plumbing problems!

Galvanized Pipes are a hollow and cylindrical structure that is most of the time in a circular cross-section but not always it is this way. It is mainly used to convey substances that can flow whether they are liquids or gases, slurries, powders, or sometimes even the masses of small solids. Pipes are also very suitable for structural applications. Pipes are an essential requirement in every household, they promote the flow of various substances that include water and gases, whether it is about the main supply or the secondary connections. Pipes serve an important purpose. Pipes can be made up of various substances like stainless steel, iron, PVC, etc. All of them are designed for various purposes and are used according to the purpose they serve. Among the pipes, there are distinctive small units of pipes with male thread allowing the connection to the other pipe on both ends. These pipes are a fitting with a male pipe thread on each end of the pipe. Which can be made with a large selection of materials such as brass, stainless steel, carbon, aluminum, and many more. These pipe nipples are used to connect other pipes or hoses together. They are an essential tool that is used in the industry of plumbing and various other industries too. Factors that are to be considered While purchasing galvanized seamless pipe fittings one must consider a lot of factors as there are different end finishes available to choose from. For instance, in the case of the pipe nipples there are varieties like; tapered pipe thread, straight pipe thread, roller cut, reamed type and chamfered type, square cut, and grooved type too. Not only that. there are a lot of things that you must already know before buying a pipe nipple, these things include factors like considering what is the tube selection, such as the material that you want, the thickness, and the diameter that is required, as it comes in various sizes and diameters. You also need to know that what general specifications are needed in order to fulfill the requirement. These specifications include factors such as temperatures, pressures, and safety coefficients. You also need to know the types of the end connections, whether the end connections are any of the type from a thread, square cut, grooved, beveled, bended, barbed or seamless. Other than the purpose of plumbing these nipples is used for purposes like waste incineration, architectural, chemical processing, pharmaceutical, food and beverage, paper, machine building, shipbuilding, semiconductor, etc.

Dec 7,2021

Things to know about threaded pipe nipples

A pipe nipple is a pipe’s short piece, usually with male or external threads in its two ends or one end used to connect two other fittings or pipes. The threads found at the pipe nipple’s two ends are available in different or same types like NPT threaded to BSP threaded pipe parts and nipple. Some Types of Nipples Barrel Pipe Nipples Sometimes, pipe nipples are called barrel nipples which, unless otherwise declared, are tapered NPT threaded at each end with an unthreaded section in their center. Threaded One End (T.O.E) Pipe Nipple Usually, this kind of nipple is employed as legs for oil tanks. They are sometimes confused with weld nipples, but real weld nipples are nipples with a beveled end finishing specifically required for butt weld connections. Weld Pipe Nipples These nipples do not have threads. They connect to tube fittings by threading versus welding and can be used in extreme conditions like temperature changes, pressure surges, and vibration. Weld nipples are undermined not by the cut threads, which can cut down the thickness of the wall and thus undermine the wall’s structural strength. Close Pipe Nipples These nipples have no unthreaded area, which tells us that when screwing of two female pipe fittings is tightly done onto these nipples’ both ends, these nipples’ tiny portion will be still exposed. Shoulder Pipe Nipples These nipples are longer than a close nipple. They include a concise, unthreaded area between the threads. The unthreaded area of shoulder pipe nipples is not massive enough for fitting a pipe wrench. Whenever two female pipe fittings are screwed onto either end, a nipple’s small piece will continue to be exposed. Hex Pipe Nipple Hex nipple has got its name from its hexagon-shaped middle section. Its hexagon shape lets the wrench safely grasp it. If you find a hex nipple with two different sizes on each end, then remember such a nipple is called unequal or reducer nipple. Right-Left hand Pipe Nipples These nipples have a left-hand thread on one end and a right-hand thread on the other hand. Usually, this type of pipe nipple is employed for piping applications where unions are not allowed or in gas piping. Right left-hand nipples can be also used for connecting female pipe threads in an installation where no room exists for a union. Swage Pipe Nipples These nipples are employed to bring the fluids’ flow from one pipe to another. Swage pipe nipples are available with threaded, beveled or plain ends. Their function is to change the pipe’s diameter and to connect two different sized pipes. Swage pipe nipples are offered in two types. These include eccentric swage nipples and concentric swage nipples. Concentric swage nipple is employed for the vertical pipeline; eccentric swage nipple is used mainly in horizontal pipelines. Seamless Pipe Nipples These nipples are seamless as they do not have a repaired seam that runs up the pipe nipples’ length. They are stronger structurally and are built for high-pressure applications.

Nov 23,2021

How To Choose The Best Galvanized Welded Pipe Nipple?

Choosing a pipe nipple or any other pipe fitting isn’t a big deal, but the quality of these fittings and nipples can determine the life of the material and how these fittings will work on the applied system or project. In this article, we reviewed every aspect of Galvanized Pipe parts and Nipples. What Is a Galvanized Welded Pipe Nipple? A small piece of fitting used for connecting two ends of a fitting is generally known as a Pipe Nipple, and if that pipe nipple has welding ribs on the inner wall, It’s a welded pipe nipple. So, what does that means by Galvanized? Galvanized means (metal coated with a protective layer of zinc). Content Table: • Material/Element of The Pipe Nipple: • Length Of the Pipe Fitting: • Price Of the Welded Pipe Nipple: • Wall Thickness/Diameter of The Welded Pipe Nipple: • End Connection of The Pipe Nipple: Material/Element Of The Pipe Nipple The material of which the fitting is made up tell the quality, life, and how the fitting work. A good quality welded pipe nipple can undergo extreme conditions and bear high pressure. Usually, welded pipe nipples are used for pressure up to 10 MPa to 1500 MPa. Length Of The Pipe Fitting A pipe nipple is one of the minor pieces of a pipe, and a welded pipe nipple generally comes in 1/8 to 12’’. You need to get all your pipe nipples of equal size, a tiny change in the length of those fittings can increase the length of your overall pipe fitting. Price Of The Welded Pipe Nipple The price of the fittings also plays a crucial role when buying Zinc-Coated Welded Pipe Nipples; usually, these things are not super expensive. However, the cost of the nipples and fittings is determined according to the material they’re made. Getting an affordable price quote can help you to be in your overall project budget. Wall Thickness/Diameter Of The Welded Pipe Nipple The diameter or the wall thickness of a welded pipe nipple determines the overall weight of the fitting. Typically, these fittings come in various diameters, and it depends on your need. The thicker the wall of the nipple fitting is, the more pressure it can bear. These welded pipe nipples measure in three sizes;  STD - Standard   XS - Extra Strong   XXS - Double Extra Strong End Connection Of The Pipe Nipple End connection means the shape of both ends of the pipe nipple. There are various end connections, and the consumer can also order their custom end connection shape of the pipe nipple. There are six standard end connections: • Plain Both Ends (PBE) • Plain One End (POE) • Threaded Both Ends (TBE) • Threaded One End (TOE) • Beveled Both Ends (BBE) • Beveled One End (BOE) Different Types of Pipe Nipples There are around five standard types of Pipe Nipples, but you can also make your custom pipe nipple according to your need. • Close Nipple: These nipples are also known as Running nipples. It is the most standard type of pipe fitting, having male threads at both ends of the nipple. Pipes have plain heads, so the connecting pipes are connected tightly. Typically, Close nipples or running nipples use for permeant connection because they’re so hard to unscrew. • Welding Nipple: Are also used for permanent connection because welding nipples have one threading end and one plain end so that the connecting pipe can weld together with the fitting.  • Hose Nipple: The most commonly used nipple in daily life. It contains a thread head at one end, and the other end has a hose bard at the other end. It is used for connecting a tube to the main pipe.    • Reducing Nipple: Also known as unequal nipple, it has two different diameters on both ends so that you can attach two different-sized pipes.   • Hexagonal Nipple: Are looks like a pipe nipple having a nut between the two ends of the fitting pipe. The purpose of this nipple is to provide a nut head so you can easily unscrew the nipple with a wrench. 

Nov 4,2021

Understanding the difference between BSP and NPT Nipples?

What is a BSP Nipple? BSP pipe nipples, also called British standard pipe threads, is a series of technical standards for screw threads. These standards are practiced and employed by plumbing services locally as well as internationally. According to BSP standards, a proper pipe fitting should interconnect and seal an external male thread with an internal female thread. The latter interconnection takes place with the help of various types of BSP threaded pipe parts. These standards have been laid out for a long time and have been adopted as standard rules in the plumbing and pipefitting industry.  What is the debate between BSP and NPT Nipples? BSP pipe nipples are often confused with NPT nipples, another type of pipe fittings used in the United States, including north and south America. NPT pipe nipples are also called National threaded pipe fittings, are American national technical standards for screw threads used for connecting different types of threaded pipes. They tend to be unique in their structure and properties. These nipples consist of tapered threaded ends as well as straight threaded ends; both of them are shaped irregularly and assist in interconnecting a male thread to a female thread. As a result, the pipe fittings tend to be rigid, withstanding any pressure and ensuring pressure-tight sealing.  BSP Vs. NPT: Which is Better? BSP and NPT specify the technical standards for pipe fittings worldwide, but depending on the country, the names change. However, BSP threaded pipe nipples are popularly known for being the number one in terms of quality, durability, and functionality. The reason is that BSP nipples are manufactured using the finest quality screw threads that are used in various plumbing applications worldwide. BSP pipes are also known as Whitworth standard pipes and enjoy the honor of ISO rating of 228. The latter are the reasons that give BSP nipples an edge over NPT nipples and the features that differentiate the two technical standards.  Applications of BSP and NPT nipples  BSP and NPT both have their respective applications and uses. Both of these standards utilize tapered and straight threads, but tapered threaded nipples steal the limelight, and there is a reason for that. Unlike straight threads, which are easy to unseal, a tapered threaded nipple can be used to ensure an air-tight connection between pipes. However, Straight pipe nipples hold the pipes together, but when a tapered nipple is used coupled with torque, it further solidifies the connection and compresses and seals the fitting. Follow us on social media platforms Twitter     Pinterest